Can you spray thompson’s water seal? Yes, you can apply your Thompson’s water seal using a standard pump garden sprayer and achieve the desired results. This sprayer is best to use when applying sealers.

Can Thompson's Water Seal be sprayed on?

The manufacturer of Thompson Water Seal recommended that you use their product with a plastic sprayer with a brass wand, such as our Chapin Premier sprayer. There are no concerns about it eroding any of the seals inside of it.

Can you apply Thompson's Water Seal with a garden sprayer?

Can You Apply Water Seal with Sprayer? Answer: The Thompson Water Seal manufacturer recommends that you use the stain with a plastic sprayer. While you can still apply the sealer with a paintbrush, a good sprayer is will be more efficient.

What is the best way to apply Thompson's Water sealer?

The fastest way to apply is with a pump-up sprayer (using a coarse setting), but you can also apply with a brush or a roller. You should apply liberally. In the case of areas with heavy discoloration or dirt, apply a second coat, brush lightly with a broom and hose off.

Can you spray Thompson's Water Seal on a fence?

Treating the Fence For the convenience of a one-day project, Thompson’s® WaterSeal® Exterior Stains can be applied to damp, freshly cleaned wood. When treating your fence and applying a Thompson’s® WaterSeal® waterproofer or fence stain, follow the label’s application instructions carefully.

How long does Thompson Water Seal last?

Water Seal can only be used on bare and uncoated brick, stone or concrete. How long will Water Seal last? If applied correctly, Water Seal will last up to 4 years. This is dependent on conditions such as orientation of the wall and local climate.

Can you put Thompson Water Seal on treated wood?

Other products, like Thompson’s® WaterSeal® Waterproofing Stain, can be applied immediately to new pressure treated lumber. New cedar and redwood can always be treated immediately.

Can you put Thompson's Water Seal on wet wood?

Thompson’s® WaterSeal® Waterproofing Stains can be applied to damp wood, so you only have to wait about two hours to begin applying stain. Some of our other products require that the wood dry for 48 hours before applying a deck coating.

Can you spray wood sealer?

You can even use a garden sprayer to apply the sealant. No fuss, no muss. … Remember to cover nearby foliage to protect them getting sprayed with sealant.

Can you apply sealer with a pump sprayer?

Yes, you can use a standard pump garden sprayer to apply your sealant. … Since solvent-based sealers have more active chemicals and corrosive agents, they are not recommended for garden sprayers. But if you’re using a water-based sealer, you can use the same sprayer you use for fertilizer and insecticide.

Article first time published on

Can you apply Thompson's Water Seal in the sun?

Applying a sealer and/or stain typically is recommended every one to three years, depending on the finishing product, deck use, weather conditions, and sun exposure. All Thompson’s WaterSeal products are DIY-friendly, and most need only a single application on a clean, dry deck.

Can you spray Thompson Water Seal with a pump up sprayer?

You should be able to work with any sprayer that gets the job done. This can be a deck stain pump sprayer or garden pump sprayer with a hose. However, Thompson’s water seal manufacturer recommends using a plastic sprayer with a brass wand attachment when applying their products.

Should you water seal your fence?

Wood is porous, so every time it gets wet, the water does a bit more damage to the fence. Instead of letting the elements take their toll, use a water seal to protect your fence and extend its life.

Is it OK to water seal pressure-treated wood?

However, most pressure-treated wood should have periodic sealing against moisture, preferably every year or so. Although the wood is resistant to rot and insect attacks because of the pressure treatment, it can warp, split and develop mildew if not protected from the effects of water.

How long should you wait to water seal pressure-treated wood?

Let it dry. Most deck sealers for PT lumber require 24 to 48 hours of drying time, so make sure there’s no rain in the forecast.

Why is my Thompson Water Seal white?

If you have white spots in the concrete there is probably water under the water coat. Maybe if the sun dries it out and the white spots go away you could try applying another coat. I would have tried DRYLOK Latex Water Proofer on your patio, I use this product on my concrete steps.…

Does Thompsons water sealer go bad?

PVC primer and Thompson’s Water Seal™, sealed tightly, can be kept indefinitely (no minimum temperature), as can concrete bonding additive if stored above freezing.

Is Thompsons Water Seal good?

Thompsons WaterSeal Advanced Natural Wood Protector – Editor’s Choice and The Best Outdoor Sealer for Wood. Thompson’s WaterSeal Advanced is a maximum strength waterproofer and natural wood protector. The coating resists mildew growth, UV damage, and fading. It’s perfect for natural wood decks, fences, and furniture.

How do you spray wood sealer?

Simply open up your stain sprayer and pour in your wood stain or mix. Then turn and seal the lid counter-clockwise to create an air seal. This allows you to build up the vacuum within the sprayer so you can spray it as needed. The sprayer will have a handle coming from the top near the hose.

Can deck stain and sealer be sprayed?

You can apply deck stain with an airless paint sprayer, but it usually has too much power to spray deck stain effectively and efficiently. A garden pump sprayer or a deck stain pump sprayer is the perfect tool to use to apply deck stain.

Why is my Thompson Water Seal sticky?

High humidity means there is a lot of moisture suspended in the atmosphere. This kind of situation impedes drying by making it difficult for the solvent particles in your sealant to escape into the air. … However, sometimes it might have sticky residue for an entire week if the humidity is significantly high.

How long does it take for Thompsons Water Seal to dry?

Allow at least 48 hours to dry; however drying time will vary depending on the substrate, temperature, and humidity. Allow minimum of 30 days drying time before applying oil based paint over Thompson’s® WaterSeal® Waterproofing Wood Protector – Clear.

Is it better to roll or spray paver sealer?

As long as you apply the paver sealer on a windless day, the coverage can be generous and effortless. If you really cant get a pump up garden sprayer, opt for a sponge-type roller to apply the sealer. A nap roller is more likely to grab and trap your joint sand. I recommend spraying when applying brick paver sealer.

Is Thompson's Water Seal oil based?

Thompson’s® WaterSeal® Penetrating Timber Oil is an oil-based product that provides protection by penetrating into wood pores and sealing out water infiltration. Thompson’s® WaterSeal® Waterproofing Stains are water-based products that have film-forming properties to protect the wood by repelling water.