Overall, only two types of power nailers work best for attaching hardie siding: siding and roofing nailers. But if you must use a framing nailer, to install any James Hardie product, be sure to fit it with a quality flush mount attachment so as to control the depth the fastener is driven.

Can you shoot nails through hardie board?

You can shoot Hardie siding on with air powered nailers or use hand driven roofing nails to attach siding to the home or structure. The nails can be ringed- shanked or smooth just make sure you are hitting the studs in the wall. … Drive nails flush with face of hardie plank but don’t counter sink nail.

What size nails do you use for Hardie board?

James Hardie recommends using stainless steel finish nails when installing HardieTrim products. Use a 2 in. finish nail to fasten trim together.

Can you nail hardie board with a framing nailer?

The answer is, yes. Framing nail guns can be used for siding installation, if the nail being used is long enough to attach the siding firmly to your exterior wood sheathing. While it’s recommended to always use a siding nail gun for siding installation, in a pinch, you may be able to use a framing nailer instead.

Can you use a roofing nail gun for siding?

Just keep in mind the main difference between them; the fasteners they use. If you’re installing siding, you want a siding nailer. For installing roofing, a roofing nailer is the best choice.

Can you use framing nailer for roofing?

Large-body nailers typically include framing nailers and roofing nailers. These nailers are used for more technical projects such as framing out a basement or installing roofing shingles. … If you’re constructing a fence, a framing nailer is a good option.

Can I use brad nailer for siding?

A pneumatic nail gun should be used for siding installation, especially for harder fiber cement siding. … You cannot use a brad gun for installing siding because the brads leave two holes for each brad and do not hold up as well as siding nails.

What kind of nails do you use for James Hardie siding?

Fasteners must be corrosion resistant, galvanized, or stainless steel. Electro-galvanized are acceptable but may exhibit premature corrosion. James Hardie recommends the use of quality, hot-dipped galvanized nails. James Hardie is not responsible for the corrosion resistance of fasteners.

What nails do I use for siding?

Use aluminum, galvanized steel, or other corrosion-resistant nails, staples, or screws when installing vinyl siding. Aluminum trim pieces require aluminum or stainless steel fasteners. All fasteners must be able to penetrate a minimum of 1 1/4” (32mm) into nailable material, such as wood sheathing and framing (Fig.

How do you attach things to Hardie board?

Generally speaking, items can be attached to Hardie® siding by using either corrosion resistant nails or screws. The fasteners must be long enough to go through the siding and into wood or metal substrate (e.g. sheathing or studs).

Article first time published on

Can you use the DeWalt roofing nailer for siding?

Cordless tools take siding installation to the next level and our Siding Adapter Tips take the DeWalt 20V roofing nailer to the next level, making it the ONLY cordless vinyl siding nailing option on the market.

What can you use a roofing nailer for?

Roofing guns are built to drive nails that are appropriate for most types of asphalt and fiberglass shingles, waterproof tar paper and insulation board. Whether you are installing a new roof, or re-roofing, roofing nailers are built specifically for what they are named.

Is it better to nail or screw Hardie board?

James Hardie recommends that nails be hot dip galvanized (at a minimum) or stainless steel (as a best practice). Anything less and the nails may start to rust, leading to stains on your beautiful siding.

What is a brad nailer?

A brad nailer is a powered nail gun that shoots 18-gauge brads (small nails). Brad nailers are used by woodworkers and especially finish carpenters to install casing and base trim up to 3/8 inches thick. … Most brad guns can shoot brads that range in length from 5/8 inches to 2 inches.

Can I use a finish nailer for roofing?

Answer: A finishing nailer will work fine. Use about 1-1/4″ long 16 gauge nails. If these are subpanels which you’re going to cover with a finished material, you could use a roofing nailer for the subpanels and a finishing nailer for the outer material where the nail heads/holes are less likely to be seen.

Do you nail or staple shingles?

Fasteners for asphalt shingles should be roofing nails or staples. The head of a roofing nail or the crown of a staple is what actually holds a shingle in place. … If staples are properly installed, they offer nearly the same wind resistance as nails.

What is the best nail gun for Hardie siding?

  • Best James Hardie Siding Nail Gun Overall: BOSTITCH Coil Siding Nailer.
  • Runner-Up: Makita Nail Gun Hardie Siding Coil Nailer 2-1/2″, Silver.
  • Best Hardieplank Nailer Budget: Freeman Pneumatic 15-Degree 2-1/2” Coil Siding Nailer.

Can you use screws on siding?

A stainless steel screw is the very best, but also the most expensive. Vinyl coated screws are great too. … No matter which screw you buy, make sure it is a Phillips head screw because they are the easiest to use. Obviously, you want to be safe when climbing ladders to drill into the siding.

Can you hammer a nail into Hardie board?

Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun. … Don’t drive nails into the siding at an angle.

Can you use screws on hardiplank?

HardiePlank® lap siding may be used with fasteners approved by ICC-ES ESR-2290 spaced in accordance with the Wind Load Tables. Fasteners must be corrosion resistant, galvanized or stainless steel. … Fasteners shall be installed between 1 in. and 3/4 in.

Can you put screws in Hardie board?

Fasten HardieBacker sheets with proper nails or screws (as listed in ”Materials Required” in the backer installation instructions) every 8” around the perimeter and all supporting studs. Keep fasteners between 3/8” and 3/4” from sheet edges and 2” in from sheet corners.

Does DeWalt have a cordless siding nailer?

The DeWalt 20V Max roofing nailer is the first cordless roofing nailer we’ve been able to get our hands on that uses just a battery for its power source. … Being the first carries some risk, and we wanted to know how well DeWalt did as the forerunner.

What size staples vinyl siding?

Staples used in a vinyl siding stapler should be 16 gauge and semi-flattened to an elliptical cross-section. The crown must be at least 7/16 inch wide and it should be long enough to penetrate a solid substrate at least ¾ inches.

What degree is a roofing nailer?

Pneumatic 15 Deg. 1-3/4 in. Coil Roofing Nailer.

What gauge is a roofing nailer?

Nail shingles, insulation boards, waterproof tar paper, fiber cement roofing, siding, vinyl and more with the WEN Pneumatic Coil Roofing Nailer. The versatile magazine holds up to 120 nails at a time, allowing for sizes of 11-gauge (. 12 inches) nails ranging from 3/4 of an inch all the way up to 1-3/4 of an inch.