Almost all local jurisdictions require a permit to install your wood stove. Some will also inspect the installation. … Most insurance companies require at least an inspection by a qualified professional before insuring a home with a wood stove.

Can I install my own wood burning stove?

Logistically, yes, you can install a wood-burning stove yourself: it’s a fairly straightforward DIY job. But there are a few reasons why we recommend you leave the installation to a professional from a competent person scheme.

What is code for installing a wood stove?

The NFPA recommends that a stovepipe be at least 18 inches from the nearest combustible material. Closer clearances are allowed in some situations (Table 1). Clearances through walls and ceilings. The NFPA does not permit a stovepipe to pass through any floor or ceiling or through any fire wall or fire partition.

Do you need permission for a wood burning stove?

There is much misconception around installing a wood burning stove and whether you need planning permission or not. Historically you may need some kind of clearance from your local authority, but with new updated changed, vast majority of cases need no formal permission.

How far should a wood stove be from a protected wall?

The standard clearance recommended by the National Fire Protection Agency is 36 inches. This means that the back of the stove should be 36 inches away from any combustible material, such as woodwork, unprotected walls, furniture and even firewood.

What do you put on the wall behind a wood stove?

The fireback is a traditional heat shield for a stove The solution of replacing the back wall with a heat-resistant material, such as heat-resistant stones or a wood stove heat shield, is often cumbersome and not always beautiful.

Can I complain about my Neighbours wood burning stove?

Local Councils are legally obliged to investigate complaints made under the Environmental Protection Act 1990 relating to public health and nuisance issues, which include smoke and fumes from fires or stoves.

How much clearance do you need for a wood burning stove?

Stove manufacturer’s usually request a certain air gap around wood burning stoves, to non-combustible materials (not to be confused with combustible materials), left and right: usually between 2″ (50mm) and 6″ (150mm).

What are the requirements for a wood burning stove?

Install a stove with adequate clearance from any combustible surfaces, including floors, walls or furniture. Any chimney must have adequate capacity, the correct height, proper location, proper clearance from combustibles and proper mechanical support to be safe.

How far away should a TV be from a wood stove?

How Far Away Should A TV Be From A Wood Stove? A general rule is that the TV should be no closer than three feet. Don’t allow the TV to be within this distance if it is closer. If the TV is within this distance, it could cause damage to the screen.

Article first time published on

What can be used as a heat shield?

A brick, stone or tile heat shield is equally effective but in a different way. These dense materials absorb lots of heat and gradually release it as air circulates around them. The simplest masonry heat shield is a cement board that is separated from the wall by one-inch ceramic spacers.

Can cement board be used as a heat shield?

Hardi cement board is an inexpensive solution that will form the foundation of an effective heat shield for any application. Hardi cement board is also designed to have ceramic, porcelain or stone tiles installed over it to cover and beautify the heat shield after it is installed.

Can you heat a whole house with a wood stove?

Wood stoves aren’t typically designed to heat an entire house but sized to warm a particular room in a home. However, installing a wood stove in the right location in a home, along with helping to circulate air between rooms, or using a stove boiler, can help to raise temperatures across a whole house.

Why can I smell next doors fire?

It could be that you’ve got broken bridges ie, the bricks that divide the chimney into separate “flues”. Having the sweep test for that, by using a brush or/and a smoke test at your neighbour’s fireplace, will determine if you’ve got broken bridges or not & crucially how far down the chimney stack it is.

Can I vent a wood stove through the wall?

Venting is an important component of all stoves. And wood, gas, and pellet stoves have different venting systems. … For instance, wood-burning stoves will always be vented through the roof of your house, but pellet-burning stoves can be vented vertically through the roof, or horizontally through the wall to the outdoors.

How close can a wood stove be to cement board?

A combustible floor must be protected by a non-combustible material (like tile, concrete board, or certified to UL-1618 or as defined by local codes) extending beneath the heater and a minimum of 6″ from each side and minimum 16″ from the front face of the stove and minimum 6″ (or the rear clearance to combustibles …

How do I fireproof a wall behind a wood stove?

Common fireproof wall ideas for behind a stove include stone, brick and tiles. The look of a wood burning stove can be enhanced by using a faux panel (such as a stone veneer look) or using a fireback.

What is considered a non-combustible wall?

Non-combustible materials are building materials that do not burn or ignite when subjected to expected levels of fire or heat. Examples of non-combustible materials include brick masonry, concrete blocks, hardy backer board, calcium silicate board, cement board, metal, and certain types of glass.

How do you know if your wood stove is certified?

If you’re trying to determine if your current wood stove is EPA certified under EPA regulations, look for the permanent metal EPA certification label on the back of the stove, or you can check to see if your model is listed in the current database of EPA-certified wood heaters.

Can you put a wood burning stove in a small room?

However, there’s no need to panic! As long as you keep your small wood burning stove at least 400mm away from any combustible material – and providing that you take the appropriate care and attention when it comes to lighting, refuelling and operating your stove – then you don’t have anything to worry about.

What are the regulations for installing a wood burner?

  • The hearth must extend at least 300mm to the front and 150mm to either side.
  • The full area of the hearth should be at least 840x840mm.
  • It must be at least 12mm thick.

How much clearance is needed for a stove?

How much space should be provided in front of a kitchen stove? A minimum clearance ‘work zone’ of 40” (102 cm) should be provided in front of a kitchen stove, with a larger 48”-60” (122-152 cm) clearance provided between other kitchen appliances.

Can I hang a TV above a wood burning stove?

Installing a TV directly above a wood stove isn’t typically recommended, but if a TV will be sufficiently protected from the heat of a wood stove it may be suitable. TVs should be placed outside of clearance distances to combustibles, and a mantel can help protect a TV from the heat.

Can you install a TV over a wood burning fireplace?

In most cases, you should not install electronics above wood-burning stoves or gas fireplaces and inserts because they produce massive amounts of heat. That heat could severely damage your tv or other electronic devices.

Can you mount a TV over a wood burning stove?

The short answer is – yes. However, to ensure your television isn’t damaged from the heat, care must be taken to ensure heat generated by the fireplace is redirected away from television. There are several ways to do this, such as installing a proper mantel and building an alcove for the television.

How close can a wood stove be to a heat shield?

Most standards specify one-inch or in some cases 7/8″ of air space behind the heat shield. Some standards specify a 2″ air space.

Can you tile behind a wood burning stove?

ANSWER – Ceramic tile behind a woodstove works very well as long as it’s installed correctly over the right type of substrate. … It’s important, though, that the tile is attached to a surface that’s not affected by heat. It’s best to use a concrete substrate like a mortar bed or a cementitious backer unit.

Is HardieBacker board heat resistant?

Hardiebacker is a brand name for a line of fiber cement boards used in construction projects. … This material has strong moisture-resistance capabilities and is also heat resistant, making it an ideal liner for projects around your fireplace.

Is concrete board fire rated?

Yes, HardieBacker® 1/4″ Cement Board is deemed noncombustible when tested to ASTM E 136 and can be used in conjunction with other noncombustible materials around a fireplace. This does not mean that clearances to combustible building materials can be reduced by using HardieBacker 1/4″.

Where should a wood stove be placed in a house?

Find a suitable location To heat your home properly, you should install your wood burning stove in a central location on the ground floor, where heat can circulate easily into nearby rooms. Keep in mind to put it where you’ll have room to load wood and remove ash [source: Woodstock Soapstone Company].

What is the lifespan of a wood burning stove?

The average life of a wood-burning stove is 10 to 20 years.