Measure, mark lightly with a pencil, and cut the NeatHeat front cover (part #’s FC-30/07-06 BW or FC-30/07-04 BW) as needed. Cutting NeatHeat can be done easily with a fine tooth hacksaw, sheet metal snips, carpet shears, or even heavy scissors.

Can you paint NeatHeat?

Yes, NeatHeat is very easy to paint requiring very little surface preparation. You can use any spray paint designed for polymers readily available at your local hardware store.

What is NeatHeat made of?

NeatHeat baseboard front cover is made of polymer and the end caps are ABS plastic. They are melt proof until approximately 460°F. You can save yourself up to USD 75 per hour in labor plus the cost of material by installing NeatHeat instead of having a plumber install new baseboard throughout your home.

Is NeatHeat safe?

NeatHeat Covers are Safe and Reliable That way, you don’t have to worry about doing a lot of work to install or maintain the covers; anything you need to do involving keeping your NeatHeat covers in top shape can be done using household products.

Can you cut NeatHeat?

NeatHeat can be cut to length with a utility knife, hacksaw, chopsaw, or even carpet shears. If you can follow basic instructions you should be able to install NeatHeat.

How do you cut baseboard heat covers?

Cut the cover at the squared line with tin snips or sheet metal scissors. Use the main portion of the blades to make the cut in stages, instead of the tip of the blades that can crimp the edges of the cut.

Can Slant Fin baseboards be cut?

You’ll find that pre-assembled Slant/Fin baseboard is surprisingly easy to handle. With Slant/Fin pre- cut lengths and telescoping accessories you can leave your hacksaw at home. … And you’re in and out in half the time you’d need with most other baseboards.

What is baseboard heating?

Electric baseboard heating systems — also known as electric resistance heating — is a form of zone heating that individually creates and controls the temperature in each room of your home. There are no furnaces, boilers, heating ducts, vents or blowers involved in distributing the heat.

Can you cut baseboard enclosures?

Baseboard heater covers require cutting to length. … Steel baseboard covers are stronger than their aluminum counterparts, but the stronger steel can rust after extended use. When exchanging a rusted or outdated cover for a new cover, it may be necessary to cut the baseboard heater to length.

How do you remove a hot water baseboard heater cover?

To remove the cover from a hydronic heater, you first need to detach it from the wall. The easiest way is to work a reciprocating saw behind it and cut the screws. After you unsnap and remove the baffle in front and disconnect the clips that hold the cover to the fins, the cover should just lift away.

Article first time published on

Can I replace baseboard covers?

Installing replacement baseboard covers is literally “a snap” due to the innovative construction. Simply remove the existing end caps and front cover; then position the Baseboarders replacement cover over the existing back plate and heater unit.

Can you replace baseboard heaters?

If you need to replace a baseboard heater, you have two choices: electric convection heaters or hydronic heaters. Both types fit snugly against baseboards in any room and can be perfectly placed under windows or near drafty doorways.

How much does it cost to replace baseboard covers?

– Time needed to replace the old covers – Minimum 20 minutes per foot. This involves removal, patching the wall and then installing the new ones. Dummy cover solution total cost: $25.67 per linear foot installed.

Can PEX pipe be used for baseboard heating?

A: Oxygen barrier type PEX pipe has an external polymer coating called EVOH or “oxygen diffusion barrier” and it’s the type used for all standard closed loop heating applications, including floor heating, baseboard/radiator heating and snow melting.

How far off the floor should baseboard heaters be installed?

Your heaters should sit at least two centimetres (three-quarters of an inch) above the floor or carpet to allow the cooler air on the floor to flow under and through the electrical element. If your carpet is especially thick, trim it down around the base of your heaters.

How do I shorten my electric baseboard heater?

  1. Isolate the zone by shutting off the valves in the supply and return lines near the boiler.
  2. Open the zone drain spigot and drain enough water out to reduce the pressure (should be less than a gallon).
  3. Close the drain.
  4. Put a drip pan under the pipes.

How do baseboards work?

Baseboard heating works through convection. … Within the baseboard, the air is warmed by a series of metal fins that have been heated through electricity. The warm air then rises from the baseboard, and the pattern repeats itself, creating a circular flow known as a convection current.

What are the pros and cons of baseboard heating?

  • Pro 1: Quiet Operation. A benefit of baseboard heating is it operates quietly, unlike forced-air systems that periodically blast air. …
  • Pro 2: Easy Installation. …
  • Pro 3: Low Installation Cost. …
  • Pro 4: Good Heating Source. …
  • Pro 5: Easily Cleaned. …
  • Pro 6: Longevity. …
  • Con 1: Costly Operation. …
  • Con 2: Takes Up Space.

Can you put furniture in front of baseboard heaters?

Baseboard heaters typically need at least 12 inches of space in front of the heater. You can place a couch or chair in front of a heater, but it must be at least a foot away. … A door that comes within 12 inches in front of a heater is a fire hazard, just like furniture that is too close to a heater.

What do you do with wires after removing baseboard heater?

Re: Totally remove electric baseboard heater Do not just put the wires back into the wall and abandon them there! If you are removing the baseboard heaters permanently then those wires most be removed to the panel or the ends placed in a metal junction box with a cover.

When should baseboard heaters be replaced?

Standard baseboard heaters normally serve their owners for about 15 to 25 years before wearing out and failing. The exact life expectancy rises and falls depending on several factors, such as quality, average outdoor temperatures and thermostat settings. They tend to last longer in homes with multiple heat systems.

Do I need an electrician to change a baseboard heater?

An electric baseboard heater requires a 20-amp circuit, according to instructions on The Spruce. You’ll also have to install a cable from the electrical service panel in your home to the baseboard heater. Installing the cable and connecting the heater should be done by a licensed electrician, though.

How much more expensive is baseboard heating?

When it comes to operating costs, however, baseboard heating represents one of the most expensive home heating options. As of March 2013, it costs $34.57 to generate one million BTUs of heat using electric baseboard heating, according to the U.S. Energy Information Administration.