DRICORE® is a floating subfloor made with a raised high-density polyethylene moisture barrier base bonded to an engineered core designed to allow air to flow underneath the subfloor system keeping floors warm and dry. DRICORE’s® engineered panels interlock easily, requiring no fastening or gluing.
What is DRIcore made of?
DRICORE® is a floating subfloor made with a raised high-density polyethylene moisture barrier base bonded to an engineered core designed to allow air to flow underneath the subfloor system keeping floors warm and dry. DRICORE’s® engineered panels interlock easily, requiring no fastening or gluing.
Do you screw down DRIcore?
Remember that DRIcore must be installed as a floating floor. Normally it is not recommended to nail, glue or screw DRIcore panels to the concrete surface. In some instances, we suggest minimal fastening of the panels to the concrete surface.
Does DRIcore subfloor glue?
Do not glue the plywood underlayment to DRICORE® panels.Do you need a vapor barrier with DRIcore?
The panels are intended to expand and contract with the seasonal temperatures of the basement. A vapour barrier over the concrete surface is not recommended. The built-in high density polyethylene membrane is the moisture barrier on the underside of the panel which allows incidental moisture to dry easily.
What is the thickness of Dricore subfloor?
The DRICORE® Subfloor R+ panels are only 1″ in thickness, less than half of the height of a conventional subfloor.
Is Dricore expensive?
DRIcore System The cost of DRIcore panels has remained below $6.50 for at least the last seven years. Its current price at Home Depot is $6.26 per panel (down from its earlier price of $6.43 per panel). Panels are approximately 2-foot by 2-foot square. This means that DRIcore costs about $1.56 per square foot.
Can you frame on DRIcore?
DRIcore® panels can be installed where there is an existing wall frame or a concrete foundation wall. Where only a concrete foundation exists, it is best to install wall framing directly on top of DRIcore® panels to elevate the floor and wall framing away from direct contact of potentially damp concrete.Should I use DRIcore basement?
As a brand, DRIcore is great for subflooring a basement with low to mid-range moisture problems. The panels are made from OSB as well as a premade moisture barrier, which is typically constructed of polyethylene or durable foam. It is a lot like insulating a floor, but with the added protection of a water barrier.
Can you build walls on DRIcore?Taking everything we know about building science, DRICORE SMARTWALL® has been developed to withstand the unique “ecosystem” of the basement environment and can be used on any concrete or block walls. … Panels can be cut to fit any desired ceiling height or basement layout.
Article first time published onIs DRIcore fire resistant?
These wood-based panels are flammable but difficult to ignite.
Can you shim DRIcore?
If one piece was a bit low or not sitting flat, we used shims from our DRIcore leveling kit to shim it up. The plastic shims can be stacked 4 high and tucked under the Subfloor panels to make everything nice and flat and level.
Is a subfloor necessary in the basement?
First, any good basement subfloor adds insulation so your feet stay warmer in winter. … Second, good subfloors provide protection of the finished flooring from lwater or water vapor moving up through the concrete, discouraging rot and mold forming underneath.
How many DriCore panels are in a pallet?
DRIcore Engineered Subfloor Panel System (pallet of 120)
Does DriCore have different sizes?
The DRICORE® Subfloor panels come in a 23.25″ x 23.25″ format and 3/4″ in height. DRICORE® Subfloor R+ panels come in the same format but 1″ in height. This size was created to provide a convenient, lightweight solution that is easy to handle and maneuver when loading into basements.
How much does it cost to install Dricore subfloor?
DRICORE System This means that DRICORE costs about $1.56 per square foot. DRICORE estimates that 205 panels are needed for this space. Total DRICORE cost is $1,281, not including tax and shipping.
How do you waterproof a subfloor?
Caulk any seams where two pieces of plywood are butted together. Dab caulk onto nail or screw heads to seal the potential leak point they provide. Caulk any splits in the wood or any other areas that may provide a point for water to seep under the subfloor.
Do you frame walls over subfloor?
If you use a product like DriCore for the subfloor, they even explicitly recommend you frame on top of their subfloor product. They do, however, recommend you screw the framing through the subfloor into the concrete with something like 3″ Tapcons spaced every 4 ft through the bottom sill of the framing.
How much is basement subflooring?
Subfloor Costs Per Square Foot. Subfloor material costs range from $1.50 to $7 per square foot, depending on the type of material.
What subfloor is best?
Plywood is considered the most popular material used for subflooring, it has been used since the 1950s and remains one of the top choices for contractors. Standard plywood works perfectly fine as a subflooring material, but the best option is ¾” tongue-and-groove plywood subflooring.
Can I put a subfloor over concrete?
How to Install a Glued Subfloor Over Concrete. … As with a floated subfloor, NWFA recommends a vapor retarder for glue-down subfloors when installing ¾” wood flooring over concrete. After installing a vapor retarder (if necessary), cut your plywood panels into 2’x8′ or 4’x4′ sections.
Do I need a subfloor on concrete?
Do I Need a Subfloor Over a Concrete Slab? While a subfloor is not necessary to add structural strength when you’ll be laying finish flooring on top of a concrete slab (as in a basement remodel), subflooring over concrete offers two other advantages: Dampness control.
How do you attach a subfloor to a wall?
Nail wall to subfloor using two 16d nails in each stud bay. – If wall is parallel to joists, nail within 1” of sheathing to hit rimboard. – If wall is perpendicular to joists, put two nails through bottom plate into each joist. First, secure the bottom of the wall.
Is my basement meant to be finished?
A basement is finished when the entire level is complete and similar to the upstairs living areas. It generally includes an electrical system, heat, finished floors, an accessible entrance/stairway, level ceilings, and finished walls. … Below are some questions that can help determine the state of a basement.
Should drywall touch the floor?
Always leave a 1/2-inch gap at the floor. This allows for floor and wall expansion without cracking the drywall. It also helps prevents moisture wicking if the floor floods. Wear work gloves, safety goggles and a dust mask when hanging drywall.
Can you shim under subfloor?
You can install thin hardwood floor shims under individual boards to make them tight. It’s best to staple or glue the shim to the subfloor to keep it from moving or squeaking in the future.
What is the best flooring for a basement?
What basement flooring options and materials are the best? The best type of flooring for basements is vinyl. Vinyl flooring can come in the form of vinyl plank and vinyl tile, giving it the ability to look nearly identical to hardwood and stone products with the added benefit of being waterproof.
Do I need a subfloor over concrete in basement?
If you don’t plan to use the space, there is no need for a subfloor or floor covering. Concrete or tile-over-concrete are acceptable floors for uninhabited basements. But to install any kind of floor covering—engineered wood, laminate, carpeting—basement subflooring is highly required.
What do you put under hardwood floors in a basement?
Solid hardwood requires a plywood sub-floor. If there is enough room (i.e. height), then you can install a 3/4″ plywood sub-floor.
What is a sub flooring?
The subfloor is the bottom most structure of the floor. It provides a flat and stable surface and supports the actual floor. … Underlayments help to provide extra support to the actual floor. While there are different types of subfloors, the most common type is made from plywood.
How do you calculate subfloor?
Area can be found by multiplying the length and width of the space in feet. Find the square footage of each space and add together to find the total square footage needed. Divide by the total square footage by the square footage of a sheet of plywood to find the number of sheets required to cover the space.
