Reset to Factory Default – Orbit Irrigation B-hyve Help. To reset your timer back to factory settings: Turn the timer to the OFF position by rotating the dial. Open the front panel and press the reset button for 10 seconds.

How do I reset my orbit sprinkler timer?

Reset to Factory Default – Orbit Irrigation B-hyve Help. To reset your timer back to factory settings: Turn the timer to the OFF position by rotating the dial. Open the front panel and press the reset button for 10 seconds.

Why do my sprinklers keep turning off?

This is almost always a problem with your timing system. Check your timing program and make sure that your duration settings are properly configured. When you make an adjustment, run a test by setting up a temporary program to turn on within a minute or two and check how long the sprinklers stay on for.

Why is my sprinkler timer not working?

If your sprinklers aren’t working but the timer is on, the problem could be a fuse. … Open the sprinkler timer box to check the fuses; if any are broken, replace them. The problem could also be the sprinkler system’s antenna, which is often powered by a 9-volt battery. Replace the battery and see if that helps.

How do I reset my orbit?

  1. Step 1: Make sure that the Orbit is powered ON. It needs to be ON to conduct factory reset.
  2. Step 2: Reset. Press & Hold the + and the – buttons together for 5 seconds. Once it’s been reset, the previously connected devices displayed on the screen will disappear.

How do you troubleshoot an orbit sprinkler system?

  1. Check the programming settings if one or more stations are not turning on. …
  2. Check the valves in the ground sprinkler controls if some of the stations are not working. …
  3. Check the Station Delay settings if sprinklers are not turning on when they are programmed to.

Where is fuse on orbit timer?

In most controllers, the fuse is located behind the control panel where the wires to the valves are connected. There should be a tab on the side of the box that will release the face of the control panel, allowing it to hinge open and give access to the fuse.

How do you tell if a fuse is blown?

Remove the fuse from its holder. In some cases you may need a small screwdriver to unscrew the fuse holder cap. Look at the fuse wire. If there is a visible gap in the wire or a dark or metallic smear inside the glass then the fuse is blown and needs to be replaced.

What is fault program on Orbit timer?

A fault message appearing on your timer or phone means that your B-hyve device is detecting a short in one of the station wires or solenoid attached to the B-hyve device. … This can be caused by a bad solenoid, crossed wires, or a short in the wire itself.

How do I change a sprinkler fuse?

Remove the fuse by grasping it between the thumb and index finger and pulling until it comes free. Inspect it visually to see if the tiny metal filament inside the glass tube is intact or broken and replace the fuse if necessary. There is often a spare fuse taped to the inside of the controller box which can be used.

Article first time published on

What does no AC mean on orbit timer?

Pro-C – “NO AC” on Display The “NO AC” display is a diagnostic message telling you that the controller has stopped receiving AC power. The controller is running on the power supplied by the backup battery. Check the power source by plugging a lamp or radio into the wall outlet to verify there is power at the outlet.

How long do sprinkler timers last?

As for its components taken separately, good quality heads will last you anywhere between 10 to 15 years, while inexpensive ones will only be good for 2 or 3 years.

How do you test orbit sprinkler valves?

  1. Turn the dial to the “Auto” position and press the “Manual” key to test the valves on Easy Dial and Easy Set Orbit timers. …
  2. Turn the dial to the “Auto” position and move the slide switch for the desired valve up to the “Manual On” position to test valves on Orbit’s “Individual Station Slide” timers.

How do you test an orbit solenoid?

  1. Turn off the water supply to the irrigation system using an isolation valve.
  2. Disconnect the solenoid wires from the controller.
  3. Using and multimeter test the number of ohms through the solenoid. 20-60 ohms – Good. …
  4. If solenoid tests Good, then the solenoid is OK.